Façade adhesive In line with DIN EN 13163

Name: Façade adhesive In line with DIN EN 13163
Brand: Würth
SKU: 089240010

Facade adhesive
ADH-INSUSHT-FACADE-B1-800ML

Art.-no. 089240010

EAN 4052703427284

All versions

Specification

1K polyurethane foam for securing insulation panels to façades

Tested product features

General construction permit issued by Deutsches Institut für Bautechnik (German Institute for Construction Technology)

Building material class B1 test certificate in accordance with DIN 4102-1:1998-05, issued by MPA Hanover

Reduces costs and amount of work required

Low material consumption

Savings in transport and storage

Time-consuming process of applying mortar no longer needed

Enables additional heat insulation

High degree of initial adhesion, even at low temperatures

Does not run — forms a firm, highly adhesive bead immediately

Resistant to low temperatures

Notice

Additional fastening of insulation boards may be required depending on the quality of the construction surface. Anchorage is always required at the foot of the building, on old plaster, concrete and on non-load-bearing surfaces. In addition, mechanical fastenings should be used from a height of 5 m.

Façade adhesive can be applied with PURlogic^® Xpress, art. no. 0891 152 4 and PURlogic^® COMBIpress, art. no. 0891 152 600, foam guns. Other guns are not compatible!

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Application

Application area

Suitable for bonding insulation panels on exterior façades, internal walls, insulating elements and drain elements. Due to its excellent adhesive properties, its reduced foaming and its ability to quickly reach its final strength, the façade adhesive is suitable for a variety of other bonding tasks in insulating panels. Fixing roof insulation, fitting reveals and formwork, adhering wall-edge stripping are just a few examples. In addition, the façade adhesive can be used for heat-insulating and low-stress filling of joints and cavities, as well as between the insulation panels, such as beneath window sills.

Adheres to Styrofoam, Styrodur, mineral wool, polystyrene and polyurethane hard foam, corrosion-protected steel sheets, fibre cement, aerated concrete, particle board, hard PVC, stone, plaster, wood and emulsion paints; however, it does not adhere to polyethylene, silicone or PTFE.

Instructions

The surfaces for attaching insulation boards must be secure, flat, clean, free from dust and grease and other impurities. It is recommended that the surfaces are moistened with water prior to applying the adhesive.

Façade adhesive can be applied with PURLOGIC Xpress, art. no. 0891 152 4, and PURLOGIC COMBIpress, art. no 0891 152 6, foam guns. Other guns are not compatible!

First apply the façade adhesive to the edges and then apply in a W shape to the insulating board surfaces. The adhesive surface percentage of the pressed-on adhesive must achieve at least 40%. The insulation board can be attached to the wall one minute after applying the polyurethane adhesive to the board. Once the panel is secured, the PU adhesive stops expanding. It is possible to adapt the alignment of the insulation board within a maximum of 5-10 minutes after fastening to the wall. Any major uneven areas in the surface must treated with coarse lime cement mortar in advance. If there are spots of uneven areas on the wall, sand the inside of the insulation board to be laid so that the outside is even. If gaps need to be retained between the panels, these can be filled with façade adhesive.

Technical information

Chemical basis	Single component polyurethane
Colour	Yellowish
Smell/fragrance	Characteristic
Tack-free after	10 min
Conditions for being tack-free	at 20°C and 60% humidity
Curing time	2 h
Fully hardening/curing conditions	Depending on: coat thickness, substrate, temperature and humidity
Min. processing temperature	5 °C
Max. processing temperature	30 °C
Min. surface processing temperature	5 °C
Max. surface processing temperature	30 °C
Min. temperature resistance	-40 °C
Max. temperature resistance	90 °C
Yield (volume) approx.	47 l
Yield (area)	10 m²
Contents	800 ml
Building material class	B1 - Of low flammability
Building material class conditions	in accordance with DIN 4102-1
Resistance against	Aging
Min. compressive strength	40 kPa
Max. compressive strength	50 kPa
Max. tensile strength	180 kPa
Min. tensile strength	150 kPa
Compressive strength conditions	in accordance with DIN 53421
Heat conductance λ	0.036 W/(m*K)
Heat conductance λ conditions	in accordance with DIN 52612
Min./max. tensile strength	150-180 kPa
Conditions for tensile strength	in accordance with DIN 53455
Shelf life from production	12 Month
Conditions to maintain shelf life from production	upright and cool storage area

Documents

Product information

Würth Catalogue (2)

Flip Book

Catalogue page as PDF 1

Datasheets (1)

Safety data sheet

Certificates/ Documents (6)

Operation manual 1

Operation manual 2

Manufacturer's declaration 1

Approval/Assessment 1

Technical data sheet 1

Technical data sheet 2

Accessory

Required accessory:

Product

Description

Quantity

Price
/PU

1C foam gun PURlogic<SUP>® </SUP>Xpress For professional application of 1-component gun foams

1C foam gun PURlogic® Xpress For professional application of 1-component gun foams

FMGUN-1C-(PURLOGIC-XPRESS)-PLA

Art.-no. 08911524

For professional application of 1-component gun foams

x 1 pcs

PU foam cleaner PURlogic<SUP>®</SUP> Clean

PU foam cleaner PURlogic® Clean

CLNR-PU-150ML

Art.-no. 089216

Quickly and simply removes fresh PU foam residue

PU foam cleaner PURlogic® Clean

CLNR-PU-PISTFM-500ML

Art.-no. 0892160

Quickly and simply removes fresh PU foam residue

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with v

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).