The images are examples. For detailed information, other images and documents, please select individual articles from the following table.
Paintable ablation coating for use in system C3
Universally applicable and paintable ablation coating as a protective coating for a wide range of media in the partition system
- Container: Bucket
- Colour: White
- Conditions to maintain shelf life from production: at 5°C to 30°C
- Shelf life from production: 18 Month
- Moulded density: 1.34 g/cm³
- Ultraviolet resistance: Yes
- Density: 1.34 g/cm³
- Resistance against: Humidity, Thawing-freezing alternations, UV radiation, Oil
Register now and access more than 125,000 products
Variants
- Easy application: by painting, with trowel or airless spraying
- Solvent-free and halogen-free
- Resistant to moisture, for indoor and outdoor use
- Resistant to frost-thaw cycles
- Insensitive to UV radiation
- Resistant to various oils and chemicals
- Free of toxic fumes
- Mechanically resistant
ETA-17/0105 / Z-19.53-2677
- Storage: Protect from frost. Storage at room temperature (+5 °C to +30 °C)
- The base material must be dry and free from dust or grease
- Spray processing/airless sprayer: (Nozzle bore
0.019 inch = 0.48 mm), stir with maximum of 2 % addition of water
| Example application of ablative coating I, brushable surface coating | Application quantity [g/m³] | Coat thickness [mm] | |
| wet | dry | ||
| 2000 | approx. 1.8 | approx. 1.0 | |
| 3200 | approx. 2.9 | approx. 1.6 | |
| 4000 | approx. 3.6 | approx. 2.0 | |
| 1000 | approx. 0.9 | approx. 0.5 | |
ETA-17/0105 / Z-19.53-2677
For use in system [C3]
- Combi AB soft partition
- Use in system C3 as a subsequent coating component of the media/partition surface
- The endothermic, weather-resistant fire protection coating is particularly suitable for large-area and high-build application quantities/layers.
- Apply with brush, roller, joint knife or airless sprayer
- Ideal application at +5 °C to +30 °C and a relative humidity of less than 85 %
- Drying time at least four hours
- 1. Clean opening
- 2. Stir the ablation coating to a brushable consistency
- 3. Coat necessary media
- 4. Coat the partition surface/AB pre-coated mineral fibre board
Services und Systeme rund ums Produkt
Mineral fibreboard AB pre-coated for use in system C3
Ablation coating I, spreadable for use in system C3
Fire-retardant coating
Ablative coating I
Mineral fibreboard With intumescent coating
Fire-retardant mortar
Assembly set For soft bulk head combi
Fire partition marking plate for cables and electrical lines
Fire-retardant filler
Combination fire protection putty
Fire protection fabric DBU 1.5
Cable duct
Combination fire protection block
KB fire protection fabric
MG III fire protection cement
Fire protection foam Kombi
FLEXEN® packing wool
Radiator paint brush DW light For dispersions and wall paints
Pipe sleeve type RK I
Flat brush LM light For solvent-based paints
Radiator paint brush LM ECONOMY For solvent-based paints
Assembly set For intumescent pipe partition
Painters' spatula Made of flexible, high-quality steel (taper ground)
DBU Red fire protection fabric
Cable box EASY With plastic lid or foam strips
Fabric adhesive tape
Assembly set For RK I/RK I Plus pipe collars
Concrete screw W-BS Compact type P with pan head
Blade, serrated
Fire protection stoppers
Ablation coating I, spreadable for use in system C3
Radiator paint brush DW For dispersions and wall paints
Painters' spatula Made of flexible, high-quality steel (taper ground)
ROCKWOOL 800
Winding wire For wrapping mineral wool insulation and intumescent strips to meet fire protection requirements
Pipe sleeve type RK I
Intumescent mat plus
Fire protection fabric DBU 1.5
Cable duct
Ablative coating I
Soft foam plugs For cable conduits
Mineral fibreboard AB pre-coated for use in system C3
Fire partition marking plate for cables and electrical lines
Nitrile chemical protective glove Long, heavy-duty design
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
