Tile dispersion primer CERAfix^® 101

Name: Tile dispersion primer CERAfix ® 101
Brand: Würth
SKU: 5875100101

Tile dispersion primer CERAfix 101
PRIM-(CERAFIX-101)-10LTR
CERAFIX

Art.-no. 5875100101

EAN 4047376963245

All versions

Specification

Solvent-free, ready-to-use, dispersion-based universal primer for indoor and outdoor use

Reduces surface absorbency

Surfaces sensitive to moisture are protected

Extends the tile adhesive drying time

Good adhesive bond

Increases the adhesion of tiles and other coverings

Deep action

Solidifying effect

Ready to use

Can be used directly from the container

No mixing required

Fast application

Blue formula

Pre-treated surfaces can be recognised quickly and easily

Water- and alkali-resistant

Suitable for indoor and outdoor use and for surfaces exposed to water

Low-odour

Solvent-free

Our products featuring the EMICODE label are low-emission/environmentally compatible. The EMICODE classification system awards labels to construction products that comply with the very stringent health and environmental requirements of recognised institutes.

Notice

CERAfix 101 must be dry before the next coat is applied. Cover surfaces not to be treated (e.g. windows and doors) prior to application. Surface must not be sticky when further work is carried out! Do not work 'wet on wet'. Protect from frost.

Recognised technical regulations apply along with current standards and ZDB information leaflets.

EMICODE EC1plus: Very low emissions: The EMICODE classification system distinguishes the environmental and health compatibility of construction products. The lowest-emission products bear the EC1plus mark.

The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting with deliberate intent. We ensure the consistent quality of our products. We reserve the right to make technical changes and further develop products.

Application

Application area

CERAfix 101 is used to prime absorbent and slightly sandy substrates made from cement and gypsum materials, concrete, plaster, masonry etc. CERAfix 101 improves adhesion, bonds builder's dust and has a solidifying effect on the substrate. Reliable at reducing substrate absorbency, thereby preventing the rapid extraction of water from fillers and tile adhesives. CERAfix 101 is used as a primer system for CERAfix seals, filler and compensating compounds and for tile adhesives in indoor and outdoor applications.

When using on calcium sulphate screeds (CA, CAF), please apply a second primer coat using CF 104.

Instructions

The substrate must be solid, load-bearing, clean, dry and free from separating substances. The material is applied with a brush or a fine-pore foam roller. Material consumption: approx. 200 g/m2. Oversaturation of the surface or puddling must be avoided. Allow CERAfix 101 to dry fully before carrying out further work. When CERAfix 101 is applied by spraying, roll or brush it again when freshly laid. Allow CERAfix 101 to dry fully before proceeding with additional steps.

Surface:

The substrate must be solid, load-bearing, clean, dry and free from separating substances. Separating materials or layers such as layers of sinter, dust, oil, rubber abrasion, paints etc. must be removed with suitable measures such as blasting, milling, sanding, suction and/or removal of oil. The surface must have sufficient load-bearing capacity for the active loads - refer to DIN 1055. The requirements regarding surface tensile strength are in line with the intended purpose. Observe the prescribed residual moistures for subsequent coverings. When doing so, ensure that the permitted residual moisture content is observed in accordance with the latest technical leaflets. The CM measurement must be conducted in accordance with the current work instruction "Interface coordination for heated floor constructions". Subsequent moisture ingress must be prevented. During application and in the week after, the air, material and surface temperature must not exceed +5 °C.

Technical information

Colour	Light blue (bright blue)
Weight of content	10 kg
Contents	10 l
Density	1 g/cm³
Viscosity/consistency	Thin fluid
Can be covered after max.	90 min
Drying time	3 h
Conditions for drying time	at 23°C and 50% relative humidity
May be walked on in following conditions	at 20°C and 65% relative humidity
Min./max. processing temperature	5 to 30 °C
Solvent-free	Yes
Min/max. application quantity in weight/area	100-200 g/m²
Min. application quantity in weight/area	100 g/m²
Max. application quantity in weight/area	200 g/m²
Application quantity conditions	depending on the absorbency of the surface
Shelf life from production	15 Month
Conditions to maintain shelf life from production	storage in a dry place protected from light, 5°C to 40°C
Sustainability	Pollutants / Emissions

Documents

Product information

Würth Catalogue (2)

Flip Book

Catalogue page as PDF 1

Datasheets (1)

Safety data sheet

Certificates/ Documents (6)

Manufacturer's declaration 1

Technical data sheet 1

Technical data sheet 2

Certification/certificate 1

Certification/certificate 2

Certification/certificate 3

Accessory

Required accessory:

Product

Description

Quantity

Price
/PU

HDPE fold masker

COVFLM-ADHSTR-55CMX33M

Art.-no. 0992405055

Statically charged, pre-folded cover film with a crepe masking tape for temporary protection of doors, windows, window sills, radiators and furniture during painting and plastering.

HDPE fold masker

COVFLM-ADHSTR-140CMX33M

Art.-no. 0992405140

Statically charged, pre-folded cover film with a crepe masking tape for temporary protection of doors, windows, window sills, radiators and furniture during painting and plastering.

HDPE fold masker

COVFLM-ADHSTR-266CMX20M

Art.-no. 0992405266

Statically charged, pre-folded cover film with a crepe masking tape for temporary protection of doors, windows, window sills, radiators and furniture during painting and plastering.

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with v

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Additive article:

Product

Description

Quantity

Price
/PU