For detailed information, other images and documents, please select individual articles from the following table.
Fire protection duct I30/I60/I90/I120
Metal fire protection duct for encapsulation of fire loads with active fire retardation
- Length: 2000 mm
- Fire resistance rating: I30, I60, I90, I120
- Surface: Zinc plated
- Material: Steel / steel
Register now and access more than 125,000 products
Variants
- No propagation of fire in the duct; actively inhibits fire
- Low space requirements as virtually the entire duct cross-section is usable
- Fast, simple installation; easily mountable, self-closing components
- Dust-free installation
- Simple fastening, even directly on ceilings or walls
- Easily accessible, therefore maintenance-friendly; easy and simple to add to installation at a later stage
- Cable versions available with metal or plastic cable fittings in accordance with EN 60 423
- Dimensionally stable
- Special designs also deliverable via special order: Two-sided, three-sided, four-sided, round duct, stainless steel duct, surfaces in RAL colours
- Fire resistance rating I 30 to I 120
- Interior coating begins to react at +200°C
- Low tare weight
- Where cables and pipes are directly supported, the permissible total weight resulting from cable and pipe dead weight is ≤ 34 kg/m
- Store in a dry and frost-free place
- When installing the fire protection duct, closely observe the installation instructions and approval Z-19.30-2214
DIBt National technical approval Z-19.30-2214
For use in system E4
Fire protection duct I 30/I 60/I 90/I 120 for encapsulation of combustibles
- Escape and rescue routes, as well as in essential corridors and stairwells
- Suitable for cables, flammable pipes and non-flammable pipes with flammable synthetic rubber insulation
- The I-duct can be routed through fire-resistant solid and lightweight partition walls
- Duct itself can act as a cable conduit
The installation instructions and general type approval Z-19.30-2214 must be strictly observed when installing the fire protection duct.
Services und Systeme rund ums Produkt
Fire protection duct end cap I30/I60/I90/I120 To be used in E4 system
Assembly set For I30/I60/I90/I120 fire protection duct
Fire protection duct inner corner I30/I60/I90/I120
Fire protection duct wall connection collar I30/I60/I90/I120
Fire protection duct flat square I30/I60/I90/I120
Fire protection duct outer corner I30/I60/I90/I120
Fire protection duct T-piece I30/I60/I90/I120
Pan head tapping screw, shape F with recessed head DIN 7981, steel, zinc-plated, blue passivated (A2K), round head, PH drive
Fire protection duct cable version I30/I60/I90/I120
Fire protection duct bracket, coated I30/I60/I90/I120
Fire-retardant divider
Fire protection duct connection rail I30/I60/I90/I120
Fire protection foam Kombi
Fire-retardant filler
Combination fire protection putty
Threaded rod DIN 976-1 (shape A) with standard metric ISO thread, zinc-plated steel 4.8, blue passivated (A2K)
Hexagon nut DIN 934, steel I6I/I8I, zinc-plated, blue passivated (A2K)
Fire partition marking plate for cables and electrical lines
Concrete screw W-BS Compact type P with pan head
Line routing duct, LFK
Flat washer For hexagon head bolts and nuts
VARIFIX® c-assembly rail 26/18
Combination fire protection block
Concrete screw with pan head W-BS/S
Drop-in anchor W-ED/S
Threaded rod DIN 976-1 (shape A) with standard metric ISO thread, zinc-plated steel 8.8, blue passivated (A2K)
Cable tie KBL 1 made of polyamide with plastic tongue
Wiring duct, VKW DIN
End piece For LFK cable routing conduit
Cable bracket for overhead mounting
Concrete screw with hexagon head W-BS/S
MFD-S straight shank multi-purpose drill bit cassette 7 pieces
Club hammer
High-performance gas unit DIGA® CS-3
Metal cavity anchor W-MH/L pan-head screw
Suction bell
Drop-in anchor W-ED/S
Stop bit with clip-on expander tool For W-ED drop-in anchors
W-DN 2 ceiling nail
Cable holder
ELMO® cable tidy holder
Assembly set For I30/I60/I90/I120 fire protection duct
Fire protection duct flat square I30/I60/I90/I120
Fire protection duct inner corner I30/I60/I90/I120
Cable bracket for overhead mounting
Wire cable holder
Wire rope On light plastic rolls
Wire cable with ending and trapezoidal plate hook
Cordless hammer drill H 28-MA vibration-dampened
Plastic multi-purpose anchor SHARK® Pro
Fixanchor W-FAZ/S
Pan head tapping screw, shape F with recessed head DIN 7981, steel, zinc-plated, blue passivated (A2K), round head, PH drive
Fire partition marking plate for cables and electrical lines
Blind rivet, open, with break mandrel and flat head ISO 15979, dome head, steel/steel
Fire protection duct cable version I30/I60/I90/I120
Fire-retardant divider
Fire protection duct bracket, coated I30/I60/I90/I120
Fire protection duct connection rail I30/I60/I90/I120
Assembly set For I30/I60/I90/I120 fire protection duct
Fire protection duct end cap I30/I60/I90/I120 To be used in E4 system
Fire protection duct wall connection collar I30/I60/I90/I120
Fire protection duct flat square I30/I60/I90/I120
Fire protection duct T-piece I30/I60/I90/I120
Fire protection duct inner corner I30/I60/I90/I120
Cable bracket for overhead mounting
Earthing clip
Fire protection duct outer corner I30/I60/I90/I120
Fire-retardant mortar
Mounting set for fire protection mortar
Fire protection foam Kombi
Application gun For fire protection foam Kombi
Assembly set For Combi fire protection foam
Cable box with foam strips
Assembly set For cable boxes
Fire protection stoppers
Combination fire protection putty
Assembly set For fire protection block/plugs
Cable duct
Ablative coating I
Soft foam plugs For cable conduits
Assembly kit for B2 system cable duct
Assembly set For I30/I60/I90/I120 fire protection duct
Cable bracket for overhead mounting
Earthing clip
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
