Surface bonding agent Primer for Metal

Name: Surface bonding agent Primer for Metal
Brand: Würth
SKU: 089010066

Bond and seal primer for metal
PRIM-BONDSEAL-PLUS-METAL-250ML

Art.-no. 089010066

EAN 4099618292392

All versions

Specification

Surface optimisation of metallic surfaces

Notice

Primer for metal reacts with moisture. To retain the quality of the primer, seal the can with the inner plastic lid immediately after each use. When pre-treatment is finished, close the can with the screw lid.

Once opened, primer for metal should be used up within approx. one month if used on a regular basis. If the can is rarely opened, use the primer within 2 months. Discontinue use of primer for metal primer if it gels, is not homogeneous or is too viscous.

Do not dilute primer for metal or mix with other substances.

Never immerse a brush or sponge in the primer in the original container.

Tip: If you only need a little, we always recommend putting only the required amount into a container, e.g. plastic cups.

Surface/material	Optimisation steps	Notes
Aluminium (AlMg3, AlMgSi1)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary.
Anodised aluminium	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	–
Steel (St 37 etc.)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary. Steel components at risk of corrosion: 2-component PU or epoxy corrosion protection required.
Stainless steel (rustproof)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	–
Zinc-plated steel (hot-dip or zinc-plated)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary.
2-component top-coat paints (PU, epoxy), 2-component water-based primers and paints, cataphoretic paints, primers (EP/2C)	B and S Activating Cleaner	Due to the large number of paints available, this information is only a guide. Where necessary, perform preliminary tests.
Powder coatings	B and S Activating Cleaner	Preliminary testing is recommended for applications involving significant forces or a damp environment.
GFRP (unsaturated polyester), gelcoat side or SMC	B and S Activating Cleaner	Lightly sand with sanding fleece beforehand if necessary.
GFRP (unsaturated polyester), layup side	1. Lightly sand with S 80 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	–
ABS	1. Lightly sand with sanding fleece 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	The sanding process can be omitted for parts subjected to little load.
Hard PVC	1. Lightly sand with sanding fleece 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	The sanding process can be omitted for parts subjected to little load.
Glass (mineral)	B and S Activating Cleaner	Adhesive surface must be protected against UV radiation (opaque cover).
Glass ceramics	B and S Activating Cleaner	–
Untreated wood and wood products (particle board)	1. Dedusting 2. B and S Adhesion Plus for P/W/S	–
Natural stone	1. Dedusting 2. B and S Adhesion Plus for P/W/S	Can cause discolouration when used with sensitive natural stone (marble).
Concrete, mineral mortar and plasters	1. Dedusting 2. B and S Adhesion Plus for P/W/S	–
Textiles, fleeces	B and S Adhesion Plus for P/W/S	Preliminary testing required; the adhesive gripping to the fabric may be sufficient.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Application

Application area

Primer for metal acts as an adhesion agent between adhesives and metallic materials (steel, stainless steel, hot-dip zinc-plated steel, aluminium, anodised aluminium, copper, brass, zinc).

Primer for metal is not an anti-corrosion protection agent.

Instructions

The substrates must be clean, dry and free from dust and grease. For pre-treatment, please refer to the optimisation table in the technical data sheet. Shake the can well. Apply adhesion primer in an evenly thin layer with a brush or felt. The flash-off time is at least 30 minutes. For more information, please refer to the technical data sheet.

Technical information

Contents	250 ml
Chemical basis	Solvent-containing primer epoxy based
Colour	Colourless, Yellowish
Min. flash-off time	30 min
Flash-off time conditions	at 23°C and 50% relative humidity
Min./max. processing temperature	5 to 40 °C
VOC concentration (CH)	63.1 %
Shelf life from production/conditions	12 Month / ≤ 25°C, sealed, upright, dry and protected from sunlight

Documents

Product information

Würth Catalogue (2)

Flip Book

Catalogue page as PDF 1

Datasheets (1)

Safety data sheet

Certificates/ Documents (2)

Technical data sheet 1

Technical data sheet 2

Accessory

Required accessory:

Product

Description

Quantity

Price
/PU

Abrasive cleaning sponge

CLNSPNG-ABRASIVE-L100MMXW20MMXH20MM

Art.-no. 0899700408

For thorough cleaning of stubborn dirt on glass panes and ceramic screen-printed edges

x 48 pcs

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).