Surface bonding agent Primer for Metal

Bond and seal primer for metal
PRIM-BONDSEAL-PLUS-METAL-250ML

Art.-no. 089010061

Prices for customers after login

Surface bonding agent Primer for Metal

Art.-no. 089010061

Prices for customers after login

Quantity

PU

In : currently piece / pieces available

Show availability in Würth branch offices

Exclusively for trade customers

Register now and access more than 125,000 products

Surface optimisation of metallic surfaces
Notice

Primer for Metal reacts with moisture. To maintain the quality of the primer, close the can immediately after use with the inside plastic cover. When pre-treatment is finished, close the can with the screw lid.


Once opened, Primer for Metal should be used up within approx. one month if used on a regular basis. If the can is rarely opened, the primer should be used up within 2 months. Discontinue use of Primer for Metal if it gels, is not homogeneous or is too viscous.


Do not dilute Primer for Metal or mix with other substances.


The previous layer must be completely set and dry before each step.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Würth Catalogue(X)

Catalogue page as PDF 1  |  2

Flip catalog

Datasheets(X)

Safety data sheet

Application area

Acts like a bonding agent between adhesives and metallic materials (steel, stainless steel, galvanised steel (hot-dip or galvanic), aluminium, anodised aluminium, copper, brass, zinc). Primer for Metal is not an anti-corrosion protection agent!

Instructions

The surface must be clean, dry and free from dust and grease. For this purpose, non-load-bearing or loose layers must first be removed. Then either spray the surfaces with a thin coating of Activating Cleaner and wipe off with a clean cloth or absorbent paper, or spray Activating Cleaner onto a cloth and wipe down the adhesive surfaces. The adhesive effect can be improved by additional pre-treatment steps such as sanding, cleaning and activating. Shake Primer for Metal well until the steel ball in the container can easily be heard. Continue shaking for a minute.


Apply a thin but opaque, uniform layer of Primer for Metal with a felt brush. Always wipe in one direction when doing so. The ideal application temperature is 15°C–25°C.


Apply Primer for Metal only once. Make sure that the layer is uniform and opaque. Observe the flash-off times!


Close the container again tightly after each use.

Chemical basis

Pigmented primer that contains solvents and improves adhesion

Colour

Yellow

Density

1.05 kg/l

Min. flash-off time

30 min

Flash-off time conditions

at 23°C and 50% relative humidity

Min./max. processing temperature

10 to 35 °C

VOC concentration (CH)

63.1 %

Contents

250 ml

Weight of content

262.5 g

Shelf life from production/conditions

12 Month / ≤ 25°C, sealed, upright, dry and protected from sunlight

Suitable glove:

 
Product
Description
Household glove
Household glove
Description:
Permeation level: 1
Liquid-proof, premium-quality cleaning glove made from natural latex
Butyl chemical protective glove
Butyl chemical protective glove
Description:
Permeation level: 2
Gas-tight and resistant to exhaust gases produced by combustion processes
Chemical protective glove made from chloroprene and latex
Chemical protective glove made from chloroprene and latex
Description:
Permeation level: 1
Cotton flocking on the inside
Nitrile chemical protective glove
Nitrile chemical protective glove
Description:
Permeation level: 1
Cotton velour lining
Nitrile chemical protective glove, heavy-duty
Nitrile chemical protective glove, heavy-duty
Description:
Permeation level: 1
Long, heavy-duty design
Natural latex and neoprene chemical protective glove
Natural latex and neoprene chemical protective glove
Description:
Permeation level: 1
Cotton flocking on the inside
Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.
Measured breakthrough time
Permeation level
< 10 min
0
≥ 10 min
1
≥ 30 min
2
≥ 60 min
3
≥ 120 min
4
≥ 240 min
5
≥ 480 min
6

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.

Hazardous Material

Product information

Würth Catalogue

Catalogue page as PDF  | 

Flip catalog

Datasheets()

Datasheets ()

CAD Data  | 

Certificates/Documents

 | 

Technical information