Spray contact adhesive BOND 90

Spray contact adhesive BOND 90

Art.-no. 0893100014

Prices for customers after login

Spray contact adhesive BOND 90

Art.-no. 0893100014

Prices for customers after login



x1 pcs
Show availability in Würth trade store

Exclusively for trade customers

Register now and access more than 125,000 products

Spray adhesive for quick and reliable bond with high adhesive force and high temperature resistance

Versatile thanks to good material compatibility and high adhesive force

  • Suitable for adhering high-quality and thicker coatings and laminates

  • Adhesive does not show through – ideal for thin or reflective surface materials

Enables simple, quick working

  • Mobile system, can be used directly from the pressure tank

  • Tension-free bonds can be processed further directly after pressing

  • No cleaning of the system is required

No thread tension

No contamination of a workpiece

Very long processing time


Ageing, water and heat-resistant for a permanent bond

Silicone-free, dichloromethane-free and toluene-free


Disposal: Do not disconnect hose from the container unless it is depressurised and emptied, and the container valve is closed. Then fully open the valve and puncture at the specified breaking point using a non-sparking tool. Dispose of in accordance with local regulations.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the wide range of applications and of storage and usage conditions, we cannot guarantee a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please also refer to the technical data sheet and the instructions for use!

Product information

Würth Catalogue(X)

Catalogue page as PDF 1

Flip catalog


Safety data sheet

Application area

Industrial, high-performance spray contact adhesive specially designed for fast and reliable bonding with a high level of adhesive force and high temperature resistance.

The adhesive is supplied in a convenient, portable, maintenance-free pressure vessel and is particularly suitable for mobile use in the workshop. The spray contact adhesive is used where fast and reliable bonding is required.

The droplet-shaped adhesive is especially suitable for high-gloss HPL, as well as for bonding wood, cork, multiplex, plywood, chipboard and decorative chipboard, wooden panels, MDF, painted steel, foam, concrete, glass, most types of plastics (such as polished GFRP, PMMA, ABS etc.), wall coverings, textiles, etc. Not suitable for polyolefin (e.g. PP, PE…), veneers, rubber and materials that contain softeners (e.g. PVC, bitumen, CV coatings, butyl, synthetic leather,…).


After connecting the hose and the gun to the pressure container, fully open the container tap. Hold the spray gun at a distance of approx. 25 cm above the workpieces to be processed. Now apply the adhesive evenly without pooling. If the application gun is too close to the surface, this may result in uneven formation. If the gun is too far away, this may result in not enough adhesive being applied. Adhesive which is too thin or much too thick can lead to bonding failure.

With highly-absorbent substrates (e.g. absorbent chipboard, OSB panels, etc.), a double adhesive application may be necessary. Apply the adhesive on the second surface at 90° (cross-wise) to the first surface.

For edge bonding, mask other areas and wet the edges with adhesive. The adhesive surface should be 100% covered (approx. 30 g/m² (hard material), about 90 g/m² (wet) per side). If necessary, the adhesive quantity should be adapted accordingly.

The drying time must be at least 5 minutes depending on the ambient temperature. The open time of the adhesive is approx. 2 hours. Using your knuckles, test whether the adhesive still has any thread tension at its thickest point (see note).

Air must have been allowed to escape from the full height of the adhesive application before the components are attached. The subsequent adhesion quality may be impaired if the adhesive is not properly ventilated. Briefly push the components together with a pressure of 2.5 – 3 kg/cm². Sufficient pressing force is essential to ensure positive adhesion. Adhesive not under tension can be processed further immediately.

The hardened adhesive joint must not come into contact with solvents or harsh industrial cleaners. The adhesive is completely cured after 24/48 hours depending on the ambient temperature. Bonds which are under tension should therefore remain held in place overnight!


Using your knuckles, test whether the adhesive still has any thread tension at its thickest point. Testing with fingertips may result in contamination of the adhesive surface from grease, dirt etc.! If adhesive remains on the knuckles, the adhesive is still too wet. If no adhesive remains on the knuckles, the components can be connected. The drying time must be precisely observed, as if the solvent has not been fully vaporised, bubbles may form in the coating material. After the drying time the adhesive remains slightly tacky. This is due to the long open setting of the adhesive!

Chemical basis

Styrene-butadiene natural rubber




0.88 g/cm³

Min./max. processing temperature

15 to 25 °C

Min./max. temperature resistance

-20 to 95 °C


22.1 l

Weight of content

14.2 kg

Shelf life from production

15 Month





Required accessory:

Application gun


High-grade metal spray gun for processing spray contact adhesive BOND 90
x 1 pcs
Connection hose


For connecting the application gun to the spray contact adhesive BOND 90
x 1 pcs
Spray nozzle BOND 90


For application gun
x 1 pcs
Press-on roller


For pressing on large areas of material bonded with contact adhesive
x 1 pcs

Packaging unit

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

Structure of our article number

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:

Information on price and image display

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units


The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.
Art.-no. ! common.detail.customermaterialnumber !

Hazardous Material

Product information

Würth Catalogue

Catalogue page as PDF  | 

Flip catalog


Datasheets ()

CAD Data  | 




Technical information