Spray adhesive

Spray adhesive

Art.-no. 0890100055

Prices for customers after login

Spray adhesive

Art.-no. 0890100055

Prices for customers after login



In : currently piece / pieces available

Show availability in Würth branch offices

Exclusively for trade customers

Register now and access more than 125,000 products

Fast-drying contact and assembly adhesive for all lightweight materials

High temperature resistance

Permanent firm hold for virtually all applications


  • Thanks to fast hardening, working material can be loaded and processed further after just a short time

  • Does not bleed through

Adjustable spray nozzle

Ideal for use in an extremely wide range of applications



Caution: Not suitable for bonding soft PVC, PVC films and particle board cutting edges. When adhering hard foam/Styrofoam, the adhesive must be applied to a small suitable area first to check compatibility, depending on the type of hard foam. After use, turn the can on its head and spray until the valve is empty.

The usage instructions are recommendations based on the tests we have conducted and on our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by the provision of this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee the consistent quality of our products. We reserve the right to make technical changes and further develop products. Please observe the technical data sheet!

Application area

For bonding paper, photos, cardboard, felt, textiles, wood, cork, decorative panels, MDF, chipboard, laminated panels, leather, steel/iron, artificial stone, rigid foam materials (e.g. Styropor®), cellular rubber, etc.

Not suitable for PP, PE, PTFE

In case of doubt, compatibility with the material to be adhered should be verified beforehand by means of testing in an inconspicuous area.


Shake can well before use. Thoroughly clean the surfaces to be adhered so that they are free of grease and dust. Depending on the material, roughen the surfaces before gluing (remove sanding dust!). On absorbent substrates (e.g. wood, felt) the application quantity should be increased.

For contact bonding, evenly spray the parts to be adhered at a distance of approx. 20-25 cm and, depending on the application thickness and room temperature, allow to flash off for approx. 5 to 10 minutes. The parts are then aligned and fitted together and pressure is applied. Their positions cannot subsequently be corrected.

For assembly bonding, evenly spray the surfaces to be bonded with adhesive on both sides at a distance of approx. 20-25 cm, but only allow to flash off briefly. The parts are joined together when still damp with adhesive; depending on the material properties, it is possible to correct the bond for a longer period of time. Do not apply a load to the bond until it has reached its final strength (approx. 24 hours).

After each spraying procedure, turn the can upside down and spray until only propellant is emitted so that neither the valve riser nor the spray head are blocked by adhesive residues. Wipe off any adhesive on the outlet nozzle.




0.728 g/cm³



Min./max. temperature resistance

-40 to 60 °C

Min. flashing point

-41 °C


Aerosol can


500 ml

Weight of content

360 g

Shelf life from production

12 Month



Suitable glove:

Nitrile chemical protective glove
Nitrile chemical protective glove
Permeation level: 5
Cotton velour lining
Nitrile chemical protective glove, heavy-duty
Nitrile chemical protective glove, heavy-duty
Permeation level: 6
Long, heavy-duty design
Natural latex and neoprene chemical protective glove
Natural latex and neoprene chemical protective glove
Permeation level: 1
Cotton flocking on the inside
Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.
Measured breakthrough time
Permeation level
< 10 min
≥ 10 min
≥ 30 min
≥ 60 min
≥ 120 min
≥ 240 min
≥ 480 min

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.